Increase In Electrical Conductivity Research Articles

Largely Enhanced Thermoelectric Performance of Flexible Ag2Se Film by Cationic Doping and Dual-Phase Engineering.

Recent studies have shown that silver selenide is a promising thermoelectric material at room temperature. Herein, flexible films with a nominal composition of (Ag1-xCux)2Se are prepared by a simple and efficient one-pot method combined with vacuum-assisted filtration and hot pressing. The thermoelectric properties of the films are regulated by both cationic doping and a dual-phase strategy via a wet chemical method. As the x increases, not only Cu is doped into the Ag2Se, but different new phases (CuAgSe and/or CuSe2) also appear. The (Ag1-xCux)2Se film with x = 0.02 composed of Cu-doped Ag2Se and CuAgSe shows a high PF of ∼2540 μW m-1 K-2 (ZT ∼ 0.90) and outstanding flexibility at room temperature. The high thermoelectric properties of the film are due to the effect of Cu doping and the CuAgSe phase, including the increase in electrical conductivity caused by doping, the enhanced phonon scattering at the Ag2Se/CuAgSe interface, and the interaction between the energy filtering effect and the doping effect. In addition to the high output performance (PDmax = 28.08 W m-2, ΔT = 32.2 K), the flexible device assembled with the (Ag0.98Cu0.02)2Se film also has potential applications as a temperature sensor.

A unified hybrid micromechanical model for predicting the thermal and electrical conductivity of graphene reinforced porous and saturated cement composites

Graphene fillers have gained widespread attention as functional reinforcements for cement composites due to their excellent physical properties. The prediction of the thermal and electrical properties of graphene reinforced cement composites (GRCCs) is of great importance for developing intelligent and multifunctional civil engineering materials and structures. In this current work, a unified hybrid micromechanical model combining effective medium theory (EMT) and Mori-Tanaka-Benveniste (MTB) is developed to simultaneously predict the thermal and electrical conductivity of the GRCCs with considering pores and saturation, in which mechanisms including phonon transport, electron tunnelling and Maxwell-Wagner-Sillars (MWS) polarization are incorporated. Graphene nanoplatelets (GNPs) reinforced cement composites (GNPRCCs) samples are prepared and tested to validate the developed unified model. The results show that the electrical conductivity of the GNPRCCs is more sensitive to saturation than the thermal conductivity. When the porosity n = 0.2 and the GNP concentration is 1 wt%, the relative thermal and electrical conductivity increases by 5 % and 193 %, respectively, when the saturation index increases from 0.6 to 1. Elongated pores are more favorable for the formation of ionic networks for electrical conductivity in the saturated GNPRCCs, while spherical pores are more beneficial for heat transport. Elongated graphene fillers are preferred for enhancing both the thermal and electrical conductivity of dry and saturated GNPRCCs. The work is envisaged to provide guidelines for developing multifunctional cement composites.

Bioassay-guided isolation of three new alkaloids from Suillus bovinus and preliminary mechanism against ginseng root rot

In order to control the occurrence of ginseng root rot caused by Fusarium solani (Mart.) Sacc., the antifungal compounds of the mushroom Suillus bovinus were investigated. And three new alkaloids (1–3), named bovinalkaloid A–C, along with one known analog (4), were isolated and identified by bioassay-guided isolation and spectroscopic analyses. Compound 1 strongly inhibited the mycelial growth and spore germination of F. solani with minimum inhibitory concentration of 2.08 mM. Increases in electrical conductivity, nucleic acid, and protein contents, and decreases in lipid content showed that the membrane permeability and integrity were damaged by compound 1. Compound 1 also increased the contents of malondialdehyde and hydrogen peroxide and the activities of antioxidant enzymes, indicating that lipid peroxidation had taken place in F. solani. Compound 1 may serve as a natural alternative to synthetic fungicides for the control of ginseng root rot.

High temperature electrical breakdown and energy storage performance improved by hindering molecular motion in polyetherimide nanocomposites

Polyetherimide (PEI) is widely used as a material for high temperature and high power energy storage capacitors in new energy vehicles and other fields. However, as the temperature increases, the electrical conductivity increases and the breakdown strength decreases, which greatly reduces the energy storage density of the capacitor and limits the application range. In order to clarify the influence mechanism of high temperature on the breakdown and energy storage performance of dielectrics, this paper established a charge capture and molecular displacement (CTMD) breakdown model based on the expansion motion of molecular segments to study the charge transport and molecular chain motion process of PEI nanocomposites (PNCs) at high temperature. The results show that at 100°C, compared with pure PEI, the internal maximum molecular displacement of PEI PNCs with appropriate doping content (3wt%) is reduced by 28.79%, and the breakdown strength is increased by 11.20%. Appropriate nano-doping can effectively increase the movement difficulty of molecular chains and reduce the activation volume that provides energy for charge transport. Thus, charge transport is inhibited, current density is reduced, and Joule heat accumulation is avoided. Finally, the high temperature breakdown and energy storage performance are improved.

Antifungal mechanisms of binary combinations of volatile organic compounds produced by lactic acid bacteria strains against Aspergillusflavus

Aspergillus flavus（A. flavus）, a common humic fungus known for its ability to infect agricultural products, served as the subject of investigation in this study. The primary objective was to assess the antifungal efficacy and underlying mechanisms of binary combinations of five volatile organic compounds (VOCs) produced by lactic acid bacteria, specifically in their inhibition of A. flavus. This assessment was conducted through a comprehensive analysis, involving biochemical characterization and transcriptomic scrutiny. The results showed that VOCs induce notable morphological abnormalities in A. flavus conidia and hyphae. Furthermore, they disrupt the integrity of the fungal cell membrane and cell wall, resulting in the leakage of intracellular contents and an increase in extracellular electrical conductivity. In terms of cellular components, VOC exposure led to an elevation in malondialdehyde content while concurrently inhibiting the levels of total lipids, ergosterol, soluble proteins, and reducing sugars. Additionally, the impact of VOCs on A. flavus energy metabolism was evident, with significant inhibition observed in the activities of key enzymes, such as Na+/K+-ATPase, malate dehydrogenase, succinate dehydrogenase, and chitinase. And they were able to inhibit aflatoxin B1 synthesis. The transcriptomic analysis offered further insights, highlighting that differentially expressed genes (DEGs) were predominantly associated with membrane functionality and enriched in pathways about carbohydrate and amino acid metabolism. Notably, DEGs linked to cellular components and energy-related mechanisms exhibited down-regulation, thereby corroborating the findings from the biochemical analyses. In summary, these results elucidate the principal antifungal mechanisms of VOCs, which encompass the disruption of cell membrane integrity and interference with carbohydrate and amino acid metabolism in A. flavus.

Transition metal-decorated MgO nanocages as drug carriers for the chlormethine drug

This paper presents a study on the potential use of transition metal (TM)-decorated MgO nanocages, namely Ni, Pd, and Pt, in improving the efficacy and safety of chlormethine (ClM). The research employs density functional theory calculations to explore the electronic properties and adsorption behavior of ClM on the surface of TM-MgO nanocages. The study also investigates the most reactive sites of ClM and TM-MgO nanocages through molecular electrostatic potential plots. The findings reveal that Ni-MgO causes significant changes in electronic properties upon ClM adsorption, with a decrease in the energy gap of frontier molecular orbitals and an increase in electrical conductivity. Meanwhile, Pd-MgO is a suitable Φ-type sensor for ClM detection. The results suggest that TM-decorated MgO nanocages could enhance the effectiveness and safety of ClM and have the potential to be used as a drug delivery system, thus warranting further investigation.

High‐Performance Thermoelectric Fibers from Metal‐Backboned Polymers for Body‐Temperature Wearable Power Devices

AbstractMetal‐backboned polymers (MBPs), with a unique backbone consisting of bonded metal atoms, are promising for optic, electric, magnetic, and thermoelectric fields. However, the application of MBP remains relatively understudied. Here, we develop a shear‐induced orientation method to construct a flexible nickel‐backboned polymer/carbon nanotube (NBP/CNT) thermoelectric composite fiber. It demonstrated a power factor of 719.48 μW ⋅m−1 K−2, which is ca. 3.5 times as high as the bare CNT fiber. Remarkably, with the regulation of carrier mobility and carrier concentration of NBP, the composite fiber further showed simultaneous increases in electrical conductivity and Seebeck coefficient in comparison to the bare CNT fiber. The NBP/CNT fiber can be integrated into fabrics to harvest thermal energy of human body to generate an output voltage of 3.09 mV at a temperature difference of 8 K. This research opens a new avenue for the development of MBPs in power supply.

High-Performance Thermoelectric Fibers from Metal-Backboned Polymers for Body-Temperature Wearable Power Devices.

Metal-backboned polymers (MBPs), with a unique backbone consisting of bonded metal atoms, are promising for optic, electric, magnetic, and thermoelectric fields. However, the application of MBP remains relatively understudied. Here, we develop a shear-induced orientation method to construct a flexible nickel-backboned polymer/carbon nanotube (NBP/CNT) thermoelectric composite fiber. It demonstrated a power factor of 719.48 μW ⋅m-1 K-2, which is ca. 3.5 times as high as the bare CNT fiber. Remarkably, with the regulation of carrier mobility and carrier concentration of NBP, the composite fiber further showed simultaneous increases in electrical conductivity and Seebeck coefficient in comparison to the bare CNT fiber. The NBP/CNT fiber can be integrated into fabrics to harvest thermal energy of human body to generate an output voltage of 3.09 mV at a temperature difference of 8 K. This research opens a new avenue for the development of MBPs in power supply.

Augmented ammonia sensing of ion-beam modified MoSe2

Gas sensors based on nanostructured transition metal dichalcogenides, such as MoSe2, are increasingly becoming important due to their low band gap, good electrical conductivity and selectivity. However, some of the parameters related to the gas adsorption can be tuned to enhance the overall sensing performance. The change of response sometimes remains low because of small number of active interaction sites on the surface. There are challenges related to slow response and slow recovery of the sensor. Furthermore, if the surface is hydrophilic, it can attract moisture, which may reduce interactions with the target gas and may also reduce the lifetime of the sensor. In this study we have used ion irradiation technique to overcome these challenges and exploit theoretical models to explain the physics behind enhanced sensing performance of 3D nanostructured MoSe2. A low energy (5 keV) argon ions have been used to induce structural and morphological modification of MoSe2. The irradiation leads to formation of Mo and Se vacancies, which is predicted by ion-solid interaction simulation and corroborated with various characterization techniques. The surface becomes superhydrophobic after irradiation and a significant increase of electrical conductivity takes place. We found that the ammonia sensing response increases by about 60 % due to the irradiation. There are further significant gains of response and recovery time of the sensor, post-irradiation. The response of irradiated samples shows more stability as compared to the pristine sample over a period of 180 days. First principles-based calculation points out that the charge transfer happens from surface to ammonia during the interaction and ion irradiation induced vacancies lead to better adsorption of ammonia in case of irradiated sample than that of the pristine sample.

Response of Phyllosphere and Rhizosphere Microbial Communities to Salt Stress of Tamarix chinensis.

As carriers of direct contact between plants and the atmospheric environment, the microbiomes of phyllosphere microorganisms are increasingly recognized as an important area of study. Salt secretion triggered by salt-secreting halophytes elicits changes in the community structure and functions of phyllosphere microorganisms, and often provides positive feedback to the individual plant/community environment. In this study, the contents of Na+ and K+ in the rhizosphere, plant and phyllosphere of Tamarix chinensis were increased under 200 mmol/L NaCl stress. The increase in electrical conductivity, Na+ and K+ in the phyllosphere not only decreased the diversity of bacterial and fungal communities, but also decreased the relative abundance of Actinobacteriota and Basidiomycota. Influenced by electrical conductivity and Na+, the bacteria-fungus co-occurrence network under salt stress has higher complexity. Changes in the structure of the phyllosphere microbial community further resulted in a significant increase in the relative abundance of the bacterial energy source and fungal pathotrophic groups. The relative abundance of Actinobacteriota and Acidobacteriota in rhizosphere showed a decreasing trend under salt stress, while the complexity of the rhizosphere co-occurrence network was higher than that of the control. In addition, the relative abundances of functional groups of rhizosphere bacteria in the carbon cycle and phosphorus cycle increased significantly under stress, and were significantly correlated with electrical conductivity and Na+. This study investigated the effects of salinity on the structure and physicochemical properties of phyllosphere and rhizosphere microbial communities of halophytes, and highlights the role of phyllosphere microbes as ecological indicators in plant responses to stressful environments.

Synergistic role of Sn-doping on the thermal and electrical properties of sinnerite Cu6As4S9

Sinnerite Cu6As4S9 has been identified as a promising material for optoelectronic applications, with potential for other energy-related applications; however, knowledge of the electrical and thermal properties as well as the mechanisms underlying transport in sinnerite is lacking. We present an investigation of the synthesis, structural, thermal and electrical transport properties of stoichiometric and Sn-doped Cu6As4S9. Sinnerite has a triclinic lattice structure, with highly distorted local atomic coordination environments that, in part, results in its complex structure and bonding. Our results and analyses indicate As 4s2 lone pair-induced distortions and strong lattice anharmonicity that leads to a relatively short phonon mean free path, resulting in intrinsically very low thermal conductivity. The electrical resistivity for both compositions, Cu6As4-xSnxS9 (x = 0, 0.2), are relatively high and varies little with temperature, typical of degenerate semiconductors. An increase in mobility and electrical conductivity was obtained by Sn doping in Cu6As3.8Sn0.2S9. This work demonstrates an effective route to synthesize bulk sinnerite as well as advances the knowledge of the properties of sinnerite, as this and other ternary chalcogenides continue to be of interest for potential technologically significant applications.

Enhancing Polyvinyl Alcohol Nanocomposites with Carboxy-Functionalized Graphene: An In-Depth Analysis of Mechanical, Barrier, Electrical, Antibacterial, and Chemical Properties.

To enhance the various properties of polyvinyl alcohol (PVA), varying concentrations of carboxy-functionalized graphene (CFG) were employed in the preparation of CFG/PVA nanocomposite films. FTIR and XRD analyses revealed that CFG, in contrast to graphene, not only possesses carboxylic acid group but also exhibits higher crystallinity. Mechanical testing indicated a notable superiority of CFG addition over graphene, with optimal mechanical properties such as tensile and yield strengths being achieved at a 3% CFG concentration. Relative to pure PVA, the tensile strength and yield strength of the composite increased by 2.07 and 2.01 times, respectively. XRD analysis showed distinct changes in the crystalline structure of PVA with the addition of CFG, highlighting the influence of CFG on the composite structure. FTIR and XPS analyses confirmed the formation of ester bonds between CFG and PVA, enhancing the overall performance of the material. TGA results also demonstrated that the presence of CFG enhanced the thermal stability of CFG/PVA nanocomposite films. However, analyses using scanning electron microscopy and transmission electron microscopy revealed that a 3% concentration of CFG was uniformly dispersed, whereas a 6% concentration of CFG caused aggregation of the nanofiller, leading to a decrease in performance. The incorporation of CFG significantly enhanced the water vapor and oxygen barrier properties of PVA, with the best performance observed at a 3% CFG concentration. Beyond this concentration, barrier properties were diminished owing to CFG aggregation. The study further demonstrated an increase in electrical conductivity and hydrophobicity of the nanocomposites with the addition of CFG. Antibacterial tests against E. coli showed that CFG/PVA nanocomposites exhibited excellent antibacterial properties, especially at higher CFG concentrations. These findings indicate that CFG/PVA nanocomposites, with an optimized CFG concentration, have significant potential for applications requiring enhanced mechanical strength, barrier properties, and antibacterial capabilities.

Approaching Technological Limit for Wet‐Pulling Technique

Carbon nanotube fibers (CNTFs) are a promising economical replacement material for contemporary metallic wired conductors due to their lightweight and advanced electromechanical properties. The wet‐pulling technique for CNTF manufacturing is highly versatile, adaptable for both laboratory as well as industrial‐scale production, and can be optimized for the maximum enhancement of electrophysical properties. Herein, a mechanosolvent‐based postfabrication approach for maximizing densification and improving electrical properties of wet‐pulled CNTFs is examined. The experimental process results in fibers achieving 60% of the theoretically maximum density and conductivity of maximally densified metallic single‐walled carbon nanotube bundles. The technique allows a corresponding increase of ≈700% in fiber density (from 100 to 704 kg m−3), a simultaneous ≈530% increase in electrical conductivity (from 748 to 3990 S cm−1), and reduced volume defects from 18% to 2%. The approach was combined with a step‐wise microstructure monitoring using focused ion beam–scanning electron microscopy to determine the mechanisms behind the optimized structures. This work is the first to provide an experimental and theoretical base for the postfabrication optimization of wet‐pulled CNTFs and lays the foundation for further enhancement with techniques such as chemical doping, fiber compounding, and combined infiltration/densification mechanisms.

Highly Transparent and Flexible Multi‐Walled Carbon Nanotubes‐Polyimide Films with Enhanced Electrical Performance as Promising Electrodes

AbstractTransparent and light films with high electrical conductivity are preferred for flexible electronic applications. In this work, a film exhibiting high transparency, electrical conductivity, and flexibility is produced using a polyimide (PI) substrate and multi‐walled carbon nanotubes (MWCNTs) through spray coating. Cost‐effective MWCNTs are used instead of other electrically conductive materials, including silver nanowire (AgNW) ink, SWCNTs, and other carbon materials. The average sheet resistance of the prepared MWCNT‐PI film is 520.2 Ω/□ (infinite for the bare PI film), which is lower than the sheet resistances of the SWCNT‐PI film reported by another group. This could be attributed to the increase in electrical conductivity of the highly transparent PI film due to the use of MWCNTs. The transparency of the MWCNT‐PI film is 71.834% at 550 nm. When MWCNTs and PI are combined, MWCNTs protrude from the surface of the PI film, creating networks and increasing electrical conductivity. Atomic force microscopy analysis revealed that MWCNT networks formed on the surface of the MWCNT‐PI film. This study suggests the possibility that MWCNTs can also be used as carbon materials for flexible and highly transparent films. Ω/□This article is protected by copyright. All rights reserved

Optimizing Bilayer Electrolyte Thickness Ratios for High-Performing Low-Temperature Solid Oxide Fuel Cells

Abstract Bilayer electrolytes for low-temperature solid oxide fuel cells (LT-SOFCs) offer the potential for higher power density by lowering the ohmic area specific resistance (ASR) and increasing the open circuit voltage (OCV) of mixed ionic/electronic conducting (MIEC) type electrolyte (e.g., GDC). However, optimizing the bilayer electrolyte thickness ratio is essential to achieve high power densities at low-temperatures (650-500℃). Herein we provide a systematic study of GDC/YCSB bilayer thickness ratios on anode-supported LT-SOFCs. In all cases the bilayer maximum power density (MPD) is higher than single-layer GDC based cells with reduced ohmic ASR values. Specifically, a high MPD of ~1 W/cm2 at 650℃ was achieved on a GDC(20 μm)/YCSB(12 μm) bilayer electrolyte based SOFC, which is 62% higher than single-layer GDC based SOFC (0.64 W/cm2) operating on humidified H2 as fuel. Such enhancement is due to the 9.3% improvement in OCV and 36% reduction in ohmic ASR values with the addition of the YCSB layer. The reduction in ohmic ASR of the bilayer electrolyte SOFCs is due to an increase of GDC electrical conductivity caused by the lower pO2 at the YCSB/GDC interface which must be considered in optimizing the thickness ratio of the bilayer electrolyte for achieving higher power density LT-SOFCs.

An In Situ-Gelling Conductive Hydrogel for Potential Use in Neural Tissue Engineering.

Cerebral cavitation is usual following acute brain injuries, such as stroke and traumatic brain injuries, as well as after tumor resection. Minimally invasive implantation of an injectable scaffold in the cavity is a promising approach for potential regeneration of tissue loss. This study aimed at designing an in situ-gelling conductive hydrogel containing silk fibroin (SF), brain decellularized extracellular matrix (dECM), and carbon nanotubes (CNT) for potential use in brain tissue regeneration. Two percent w/v SF hydrogels with different concentrations of dECM (0.1%, 0.2%, or 0.3% w/v) and CNTs (0.05%, 0.1%, or 0.25% w/v) were fabricated and characterized. It was observed that with the addition of dECM, the porosity decreased, whereas swelling and electrical conductivity tended to increase. The addition of dECM also led to a faster resorption rate, but no significant change in compressive modulus. Addition of CNTs, on the other hand, led to a denser, stronger, and more regular porous structure, higher swelling ratio, faster gelation time, slower degradation rate, and a significant increase in electrical conductivity. dECM and CNTs combined together resulted in superior porosity, swelling, resorption rate, mechanical properties, and electrical conductivity compared with SF scaffolds containing only dECM or CNTs. Hydrogel samples containing 2% SF, 0.3% dECM, and 0.1% CNTs had a high porosity (58.9%), low swelling ratio (15.9%), high conductivity (2.35 × 10-4 S/m), and moderate degradation rate (37.3% after 21 days), appropriate for neural tissue engineering applications. Cell evaluation studies also showed that the hydrogel systems support the cell adhesion and growth, with no sign of significant cytotoxicity. Impact statement Tissue loss and formation of a fluid-filled cavity following stroke, traumatic brain injury, or brain tumor resection lead to sensorimotor and/or cognitive deficits. The lack of a healthy extracellular matrix in the cavity avoids the endogenous cell migration and axonal sprouting and may also worsen the secondary injuries to peri-lesional tissue. Due to the brain anatomy, simple implantation of tissue engineering scaffolds to the injured site is not possible in many cases. Therefore, the development of injectable scaffolds that support neural growth and differentiation is crucial for tissue repair or limiting the expansion of damage region.

Ionic conductivity of nanocrystalline γ-AgI prepared by high-energy ball milling

Abstract The compound AgI crystallizes, depending on temperature and pressure, with various crystal structures. While α-AgI is the stable form at elevated temperatures, the β and the γ forms exist at lower temperatures. Variants with stacking sequences different than in pure β-AgI and γ-AgI enrich the complex crystallographic situation for AgI. In the study presented here, we converted a mixture of β-AgI and γ-AgI into nanostructured γ-AgI by mechanical treatment, that is, by high-energy ball milling of such a mixture under ambient conditions. Our work extends an earlier study by Ahmad (Z. Naturforsch. 2015, 70b, 17). We used variable-temperature, potentiostatic conductivity spectroscopy as well as electric modulus measurements to characterize the electric transport parameters. For the case that the sample is heated to temperatures near and above 420 K, preliminary information on the “resistance” of the electric conductivity against healing of defects are also collected. As compared to the unmilled but mixed sample, whose Ag+ ionic transport is dominated by those ions residing in the γ-phase of AgI (0.25 eV vs. 0.46 eV in β-AgI), ball milling only leads to a small increase in overall electric conductivity (by a factor of 3–4) for nanocrystalline γ-AgI (0.25 eV). This observation is perfectly in line with a recent observation for the fast ion conductor Li10GeP2S12 (Hogrefe et al., J. Am. Chem. Soc. 2022, 144, 9597): In materials with already rapid diffusion pathways, nanostructuring and the introduction of defects and distortions do not lead to significantly enhanced ion transport. Here, a careful analysis of data from conductivity and modulus spectroscopy helps identify which dynamic parameters are mainly responsible for the change in the overall conductivity upon mechanical treatment of coarse-grained γ-AgI.

Effects of temperature, cultivar, and storage duration of rice on physiological parameters and head rice yield

Reducing rice post-harvest losses is a global demand. This study evaluated the effects of rice storage time (initial, 30, 60, 90, 120, and 150 d), temperature (15, 20, 25, and 30 °C), and cultivar (IRGA 424, IRGA 424RI, and IRGA 431CL) on physiological properties and head rice yield. Moisture, germination, vigor, electrical conductivity, thousand-grain weight, head rice yield, and colorimetric profile were analyzed. IRGA 424 was more susceptible to the parameters evaluated, through the increase in electrical conductivity and reduction in vigor, while IRGA 431CL showed greater reductions in whole grain yield as a function of increasing storage time and temperature. In general, the temperature of 15 °C is the most suitable for maintaining the quality parameters evaluated in this study. Storage at 15 °C allowed for the maintenance of the physiological quality of the seeds, the best head rice yield, and the least change in the color profile when compared to those at higher temperatures (25 and 30 °C).

Dielectric Analysis of Amine Modified Nano-graphite: Effects of Thickness, Temperature and Frequency

Amine modified nano-graphite (NH2-NG) has been produced from nanographite (NG) powder via liquor ammonia (NH3) aqueous solution by microwave, ultrasonic methods. The surface modified NG have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR) techniques which clearly demonstrate that synthesis of NH2-NG was successful. The crystalline characteristics of amine modified nanographite powder have been studied through XRD technique. The morphology structure of synthesized surface modified nanoparticles has been determined by SEM analysis. FTIR spectra confirmed the existence of amine groups on the surface of produced nano-graphite powder. NH2-NG pellet was prepared to analyse its dielectric properties as a function of thickness (1, 2, 3, 5 and 7 mm), frequency (range 10−2-105 Hz) and temperature (25, 50, 75 and 100 °C). As a function of frequency, the dielectric loss tangent and permittivity each exhibit a distinct relaxation peak that grows up to a thickness of 5 mm then decreasing. Because nanoparticles are capacitive, the capacitance values of NG and NH2-NG increase with thicknesses up to 5 mm and drop with frequency. The drop in dielectric permittivity of NG and NH2-NG pellets after 5 mm may be caused by an increase in resistivity. Positive temperature coefficient (PTC) of increased conductance is confirmed by the continuous increase in electrical conductivity of NG and NH2-NG with temperature. The degree of temperature has a significant impact on the dielectric loss tangent, dielectric permittivity, and electrical conductivity of NG, and NH2-NG.

Enhanced electrical performance of LiMnPO4 by carbon coating for solid-state battery applications

High-energy ball milling was employed to fabricate LiMnPO4 coated with varying carbon ratios (3%wt, 7%wt, and 10%wt), using glucose as a carbon source. The process involved pre-milling of LiMnPO4 precursors, followed by granulation through high-energy ball milling at 270 rpm for 2 h, and subsequent calcination at 700 °C without an inert gas flow. XRD analysis discerned the phases and structure of LiMnPO4, confirming the successful attainment of a single-phase LiMnPO4 without impurities. Rietveld refinement of the XRD data elucidated the crystallographic details, affirming the material's orthorhombic olivine structure with precise lattice parameters, thereby underpinning the structural integrity essential for electrochemical applications. FE-SEM analysis revealed uniformly distributed semi-sphere particles, with sizes ranging from 130 nm for LM to 183 nm for LM-10%C. FTIR analysis delineated the internal modes of vibration in the olivine structure and verified the presence of carbon on the powder surface. Electrical measurements conducted within the frequency range of 20 Hz–100 kHz demonstrated an increase in electrical conductivity with an escalation in carbon concentration, ranging from 31 μΩ−1m−1 to 75 μΩ−1m−1 for 0%C and 10%C, respectively. A temperature-dependent study spanning 30–160 °C revealed stable electrical conductivity behavior for the samples, with a marginal increase observed at elevated temperatures.